web analytics
Home  >  Blog  >  Glycerin Ethoxylates and Sorbitol Ethoxylates: Properties and Where They Are Used

Glycerin Ethoxylates and Sorbitol Ethoxylates: Properties and Where They Are Used

Glycerin Ethoxylates and Sorbitol Ethoxylates Properties and Where They Are Used

Direct answer

Glycerin ethoxylates and sorbitol ethoxylates are non-ionic polyol ethers made by reacting glycerin or sorbitol with ethylene oxide. They act as humectants, emollients, lubricants, solubilisers and chemical intermediates, and are used in personal care, textiles, paper, adhesives, coatings and polymer manufacture. Their behaviour depends mainly on the number of ethylene oxide units attached.

Key takeaways

  • Both materials are polyols grown with ethylene oxide, so they are hydrophilic, non-ionic and have no fatty tail. They are not surfactants in the usual sense.
  • The degree of ethoxylation drives viscosity, water affinity and hydroxyl content, so the average EO number should appear on every specification.
  • Glycerin-based grades start from three reactive sites and sorbitol-based grades from up to six, which affects viscosity, branching and use as a reactive intermediate.
  • Main uses include humectancy in cosmetics, lubrication and conditioning in textile processing, plasticising in paper and films, and polyol feedstock in polymer chemistry.
  • Key checks before purchase are hydroxyl value, water content, pH, colour, and residual ethylene oxide and 1,4-dioxane levels.

What are glycerin ethoxylates and sorbitol ethoxylates?

Glycerin ethoxylates are polyether polyols made by reacting glycerin with ethylene oxide. Sorbitol ethoxylates are made the same way from sorbitol, a six-hydroxyl sugar alcohol.

Three terms frame the topic:

  • Ethoxylation is the addition of ethylene oxide (EO) units to a molecule that carries reactive hydrogen, such as the hydroxyl group of an alcohol.
  • Degree of ethoxylation is the average number of EO moles added per mole of starting polyol. It is the main variable that separates one grade from another.
  • INCI names for personal care use follow the pattern Glycereth-n and Sorbeth-n, where n is the average number of EO units, under the International Nomenclature of Cosmetic Ingredients.

Glycerin has three hydroxyl groups and sorbitol has six, so each can grow several polyoxyethylene chains from one core. The result is a branched, hydrophilic molecule with no fatty tail.

For that reason these materials are not classic surfactants. They behave as humectants, solubilisers, softening agents and reactive intermediates, which is why they are grouped as polyol ethoxylates rather than with fatty alcohol ethoxylates.

How are they made, and how does the degree of ethoxylation change their behaviour?

They are made by base-catalysed addition of ethylene oxide to the polyol in a closed reactor. The number of EO units fed per mole of polyol sets the molecular weight and most physical properties.

A typical production sequence runs as follows:

  1. The polyol and an alkaline catalyst, commonly potassium hydroxide, are charged to the reactor.
  2. Water is removed under vacuum and heat, because moisture generates polyethylene glycol (PEG) as a by-product.
  3. Ethylene oxide is fed under controlled temperature and pressure in a nitrogen-blanketed vessel.
  4. The batch is held for a digestion period so that residual ethylene oxide reacts.
  5. The product is stripped, neutralised and filtered to meet the target hydroxyl value, pH and colour.

Sorbitol needs extra care because it can partly cyclise to sorbitans at high temperature, which changes the functionality of the final product. Commercial sorbitol is also often supplied as a water solution, so the quality of dehydration directly affects the by-product profile.

In general, as the degree of ethoxylation increases:

  • Molecular weight and viscosity rise, and very high-EO grades can be waxy or semi-solid at room temperature.
  • Water affinity increases and the product behaves more like a PEG.
  • The number of hydroxyl groups per gram falls, so low-EO grades are more reactive as chemical intermediates.

Grades are also a distribution, not a single molecule. Two lots with the same average EO number can differ in how many short and long chains they contain.

What are the key properties of glycerin and sorbitol ethoxylates?

The defining properties are hydrophilicity, hydroxyl functionality, humectancy and low volatility. Their values shift with the EO number and with the starting polyol.

  • Appearance and viscosity: Most grades are typically clear to pale yellow, viscous liquids. Sorbitol-based grades are generally more viscous than glycerin-based grades at similar EO levels because of the larger, more branched core.
  • Solubility: Medium and high-EO grades are typically soluble or dispersible in water and polar solvents, while solubility in oils and non-polar solvents is limited.
  • Humectancy: Ether oxygens and free hydroxyl groups bind water, which slows drying in films, inks and cosmetic emulsions.
  • Hydroxyl value: This is the amount of potassium hydroxide, in milligrams, equivalent to the hydroxyl content of one gram of sample. It indicates reactivity and is commonly measured by ASTM D4274.
  • Water content: Water interferes with isocyanate and other reactive uses. It is commonly measured by Karl Fischer titration, for example ASTM D4672 for polyols.
  • Ionic character: Non-ionic and stable across a broad pH range, although residual alkaline catalyst can raise pH if the product is not neutralised.

Compared directly, glycerin ethoxylates tend to be lower in viscosity and easier to handle, while sorbitol ethoxylates offer higher functionality and more branching, which suits cross-linking, film-forming and higher-viscosity systems.

Biodegradability varies with chain length. Highly ethoxylated polyethers typically degrade more slowly than short-chain products, so test data should be requested for the exact grade.

Where are glycerin ethoxylates and sorbitol ethoxylates used?

They are used wherever a water-compatible, low-volatility polyol is needed to retain moisture, condition a surface or react into a polymer. Common sectors include:

  • Personal care and cosmetics: Humectants and skin-conditioning agents in creams, lotions and cleansers. INCI names such as Glycereth-26 and the Sorbeth series appear on ingredient lists.
  • Textiles: Components of fibre lubricants, softening finishes and antistatic preparations, where they add slip and moisture retention.
  • Paper and packaging: Humectants in coatings and, in starch-based films, plasticisers that help control brittleness.
  • Polyurethanes and resins: Polyol feedstock or chain extender, where hydroxyl value and water content set reactivity. Hydrophilic grades are used in water-dispersible systems.
  • Adhesives and coatings: Humectants that extend open time and reduce skinning.
  • Inks: Humectants in water-based and inkjet inks that limit nozzle drying.
  • Metalworking and lubricant formulations: Water-soluble components in water-based fluids.
  • Chemical intermediates: Starting materials for esters and other derivatives.

Use depends on grade. A cosmetic grade needs a controlled impurity profile and an INCI-compliant description, while an industrial polyol grade is judged mainly on hydroxyl value, water content and colour.

How to choose between glycerin ethoxylates and sorbitol ethoxylates

Start from the function the material must perform, then match functionality, EO number and purity to it. Glycerin ethoxylates suit lower-viscosity systems that are easier to handle, and sorbitol ethoxylates suit systems that benefit from higher functionality.

A practical selection sequence:

  1. Define the role. Humectant, lubricant, plasticiser, solubiliser and reactive polyol each point to different grades.
  2. Set the target EO number. Higher EO increases water affinity and viscosity. Lower EO increases hydroxyl content per gram.
  3. Choose the functionality. A glycerin core offers three hydroxyl starting sites and a sorbitol core up to six, which affects branching and cross-link density.
  4. Check the purity profile. Specify water, hydroxyl value, pH, colour, PEG content, and residual ethylene oxide and 1,4-dioxane limits suited to the end use.
  5. Confirm regulatory fit. Cosmetic, food-contact and industrial uses each need different documentation.
  6. Test in the real system. Compatibility, viscosity at working temperature and storage stability are best confirmed in a laboratory or pilot trial.

Handling and cost also matter. Viscous grades may need gentle heating to pump, and cost typically follows the raw material, the degree of ethoxylation and the level of purification.

Standards, compliance and handling for glycerin and sorbitol ethoxylates

Compliance depends on the end use, because the same chemistry is regulated differently in cosmetics, food contact and industrial supply. The main frameworks are:

  • Cosmetics: Regulation (EC) No 1223/2009 in the European Union requires cosmetic ingredients to be safe under normal use, and INCI names from the Personal Care Products Council govern labelling. The Cosmetic Ingredient Review panel publishes safety assessments for many ingredient families.
  • Chemicals registration: Substances placed on the EU market in volume generally need registration under REACH (Regulation (EC) No 1907/2006). Registration status should be confirmed for the exact substance and tonnage band.
  • Test methods: ASTM D4274 (hydroxyl value), ASTM D4672 (water content) and ASTM D4662 (acid and alkalinity numbers of polyols) are common references.
  • Safety data: A GHS-format safety data sheet (SDS) should accompany every grade.

Two impurity points deserve attention. Ethylene oxide is classified by the International Agency for Research on Cancer as carcinogenic to humans (Group 1), so residual levels are controlled in finished products. 1,4-Dioxane is a by-product that can form during ethoxylation, and cosmetic specifications limit it, with limits that vary by region.

Handling follows the SDS. Store in sealed containers away from moisture, because the materials are hygroscopic. Keep them away from strong oxidisers, and avoid long exposure to hot air, since polyethers can form peroxides over time. Shelf life is commonly stated in the range of 12 to 24 months for sealed storage, but the figure varies by grade and should come from the supplier’s data sheet.

Common mistakes and things to check before buying or specifying

Most problems come from incomplete specifications, not from the chemistry. These checks apply when approving a grade or comparing a manufacturer, supplier or exporter of glycerin ethoxylates and sorbitol ethoxylates:

  • Specifying by name only. Names such as Glycereth-26 or Sorbeth-30 describe an average EO number, not a full specification. Add hydroxyl value, water, pH and colour limits.
  • Treating them as surfactants. Without a fatty tail they do not emulsify oils on their own.
  • Ignoring water content. Hygroscopic grades pick up moisture in storage and can disrupt reactive uses.
  • Skipping impurity data. Ask for residual ethylene oxide, 1,4-dioxane and free PEG figures where the application is sensitive.
  • Confusing look-alike materials. Polyglycerols, polyglyceryl esters, polysorbates and PEG esters are different chemistries.
  • Not checking lot-to-lot consistency. A certificate of analysis for every batch, using the same test methods each time, shows whether a manufacturer controls its process.
  • Overlooking documentation and logistics. Confirm the SDS, technical data sheet, registration status, packaging options (drums, IBCs, bulk tankers) and lead time for the target market.
  • Approving without a sample trial. Compatibility, viscosity and colour after heat ageing are best verified on a sample before a bulk order.

Conclusion: what to decide next

Glycerin ethoxylates and sorbitol ethoxylates are hydrophilic polyol ethers whose performance is set by the starting polyol and the degree of ethoxylation. Decide the function first, whether humectant, lubricant, plasticiser or reactive polyol, then fix the EO number, hydroxyl value, water content and impurity limits for that use.

If you are evaluating glycerin ethoxylates or sorbitol ethoxylates for a specific application, request a technical data sheet, compliance documents and sample specifications from your shortlisted manufacturers and suppliers before finalizing.

What is the difference between glycerin ethoxylates and sorbitol ethoxylates?

Glycerin ethoxylates start from a three-hydroxyl core and sorbitol ethoxylates from a six-hydroxyl core. At the same ethylene oxide level, sorbitol-based grades are typically more branched and more viscous, with higher functionality. Glycerin-based grades are usually easier to handle. Both are hydrophilic, non-ionic and free of fatty chains.

Are glycerin ethoxylates surfactants?

Not in the usual sense. A surfactant needs both a water-loving and an oil-loving part, and glycerin ethoxylates have only a hydrophilic polyether structure. They act as humectants, solubilisers, lubricants and intermediates. Fatty esters of these polyols, such as ethoxylated sorbitan esters, do act as surfactants.

What does Glycereth-26 do in cosmetics?

Glycereth-26 is the INCI name for a glycerin ethoxylate with an average of 26 ethylene oxide units. In cosmetics it acts mainly as a humectant and skin-conditioning agent, helping creams and lotions retain water. Exact performance depends on the concentration and the rest of the formulation.

Which degree of ethoxylation suits a humectant or lubricant use?

Medium and high-EO grades suit water-based humectant and lubricant uses because they dissolve readily and have low volatility. Low-EO grades suit reactive uses, where more hydroxyl groups per gram matter. The right level depends on viscosity, compatibility and the target hydroxyl value, so confirm it by sample trial.

How long can glycerin ethoxylates be stored?

Shelf life is commonly stated at 12 to 24 months in sealed containers stored in a cool, dry place, but it varies by grade and by supplier. Because the materials are hygroscopic, opened containers should be resealed promptly, and water content and colour should be rechecked after long storage.

Are sorbitol ethoxylates the same as polysorbates?

No. Polysorbates are sorbitan fatty acid esters that have been ethoxylated, so they carry a fatty chain and act as surfactants. Sorbitol ethoxylates contain no fatty acid. They are hydrophilic polyols used as humectants, polymer intermediates and conditioning agents. The names look similar, but the structures and functions differ.

How should a buyer evaluate a glycerin ethoxylates manufacturer or supplier?

Ask for a technical data sheet, safety data sheet, and certificate of analysis with named test methods, plus impurity data such as residual ethylene oxide and 1,4-dioxane. Compare lot consistency, registration status, packaging options and lead time, and request a sample for application trials before placing a bulk order.

wordpress theme by jazzsurf.com